- Manuals
- Brands
- Indoor Furnishing
- S-cape
- Owner's manual
Hide thumbs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Table Of Contents 21
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
- Table of Contents
-
Advisory
-
Electrical Grounding
-
Lubrication
-
Product Ratings
- Lifting/Lowering Mechanisms
-
Message Operation
-
Location Environment
-
-
Acoustics
- Installation
-
Headboard Bracket Installation
-
Turnbuckle Adjustment
- Troubleshooting
Advertisem*nt
Quick Links
- 1 Table of Contents
- 2 Lifting/Lowering Mechanisms
- 3 Installation
- 4 Troubleshooting
- Download this manual
OWNERS MANUAL
[ power foundations ]
99300787-k EDR11739 4/11
S·cape
®
S·cape
Platform
®
Silhouette
™
Pro-motion
™
Bronze
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for Leggett & Platt S-cape
-
Adjustable beds (24 pages)
-
1 piece models (19 pages)
-
Adjustable bed (20 pages)
-
Adjustable base bed (20 pages)
-
(16 pages)
-
Adjustable base (6 pages)
-
(6 pages)
-
Foldable base q/k/ck (16 pages)
-
Adjustable base (20 pages)
-
(24 pages)
-
(24 pages)
-
(24 pages)
-
Custom choice collection ultra furniture design (28 pages)
Summary of Contents for Leggett & Platt S-cape
- Page 1 99300787-k EDR11739 4/11 S·cape ® OWNERS MANUAL S·cape Platform ® Silhouette ™ Pro-motion ™ Bronze [ power foundations ]...
-
Page 2: Table Of Contents
cONtENtS Advisory ........................3 Acoustics ........................5 Installation ......................... 6 Turnbuckle Adjustment ....................18 Troubleshooting ......................19 If power foundation does not operate or if parts are missing, call: 800-888-3078 Do not contact retail store or dealer. -
Page 3: Advisory
AdviSORy important information READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT This Power Foundation has been quality engineered with design features to assure comfort and safety when operated properly. PROdUct RAtiNgS ELEctRicAL gROUNdiNg The bed lift motors are not designed for This product is equipped with a polarized or continuous use. - Page 4 AdviSORy important information READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT This Power Foundation has been quality engineered with design features to assure comfort and safety when operated properly. SMALL cHiLdREN / PEtS WARNiNg fcc cOMPLiANcE After the bed is unboxed, immediately dispose Electrical components are rated for 110/120 of packaging material as it can smother small voltage, 60Hz, 3.9 amp.
-
Page 5: Acoustics
AcOUSticS LiftiNg/LOWERiNg MEcHANiSMS LOcAtiON ENviRONMENt The lift/lower feature will emit a minimal The level of sound experienced during humming sound during operation. This is operation is directly related to the location normal. environment. For example, when a bed is located on a hardwood floor with the massage During operation, the lift arm wheels make feature in operation, a vibrating tone will be contact with the platform support of the bed. -
Page 6: Installation
• (1) Accessory Sheet • (1) Warranty Sheet • (1) Warranty Activation Card • (1) Power Foundation Quick Setup Guide (4 pieces) *S-cape and S-cape Platform are type a bed base ® ® frames. Silhouette™, Pro-Motion™, and Bronze are type b bed base frames. - Page 7 iNStALLAtiON StEP 2 Carefully lift the bed base frame from the shipping carton, keeping the unit top-side-down. StEP 3 Install (4) legs into the base frame. Simply screw each leg into a tapped hole at each corner of the base frame (FIGURE 1). Insert casters into the bottom of each bed leg.
- Page 8 iNStALLAtiON StEP 5 For beds equipped with power down box, install (2) 9 volt batteries into the receiver unit (FIGURES 2 and 3). Note: Beds not equipped with a power down box do not require batteries. press in (slightly) and push dow to remove battery compartment door...
- Page 9 iNStALLAtiON StEP 6 Remove the plastic packaging from the bed base frame. Carefully rotate the base frame over to position the bed top-side-up. StEP 7 Plug electrical power cord into a working, grounded electrical outlet. Note: an electrical surge protection device is recommended (not included). StEP 8 If hand control is non-wired type, install batteries in hand control (wired hand controls do not require batteries).
- Page 10 iNStALLAtiON b. Place mattress retainer ends into grommeted holes in top surface of adjustable bed base (FIGURES 5 and 6). Press down until horizontal retainer section is flush against bed base. mattress retainer figure 5: mattress retainer installation. figure 6: mattress retainer installed. NOTE: If bed is to be set up without a headboard, basic installation is now complete.
- Page 11 Install headboard brackets to the bed base frame*. When attaching (2) twin size units to a king size headboard an optional swing hinge kit (see accessory section) may be used to connect the twin units. * S-cape and S-cape Platform are Type A bed base frames.
- Page 12 iNStALLAtiON StEP 11 Install headboard brackets to the bed base frame as follows: Note: Headboard brackets are optional for Type B beds. See accessory sheet for order information. a. Raise the head section of the bed (with hand control) to gain access to the bed base frame.
- Page 13 iNStALLAtiON c. For bed base Type B, locate channel connector kit (FIGURE 10). On one side of bed base frame, locate (2) holes for channel connector mounting (FIGURE 11). 74” base length 80” base mounting length holes mounting holes figure 10: channel connector kit. (Used with bed base Type B. See accessory sheet).
- Page 14 iNStALLAtiON d. Position channel connector so that the flat side is flush against bed base frame. Attach channel connector to bed base frame using (2) 1½ inch long hex head bolts/nuts (FIGURE 12). Tighten bolts. Note: For beds with 74” base length, use inner mounting holes.
- Page 15 iNStALLAtiON e. Using (2) 3 inch long carriage bolts/nuts, attach (1) headboard bracket channel to bed base frame (bed base Type A) (FIGURE 13) or (1) channel connector (bed base Type B) (FIGURE 14). Hand tighten bolts/nuts (loosely) to allow adjustment of the headboard bracket channels.
- Page 16 iNStALLAtiON f. Attach (1) headboard bracket flange to one of the bracket channels with (2) 1 inch long hex head bolts/nuts (FIGURES 15 and 16). Tighten bolts. g. Repeat procedure to attach the other headboard bracket. headboard bracket flange use (2) 1 inch long heX head bolts to attach bracket flange to bracket channel adjustable...
- Page 17 iNStALLAtiON h. When installing a headboard, footboard, or four-piece surround (case good), allow for 1.5 inches (38.1mm) to 2 inches (50.8mm) of clearance at the head and foot of the bed and a minimum of ½ inch to ¾ inch on the sides (FIGURE 16).
-
Page 18: Turnbuckle Adjustment
tURNbUckLE AdjUStMENt If the foot end of the bed base becomes unlevel (figURE 1), adjust by following the numbered instructions below. StEP 1 figure 1 On one side of bed base, loosen jam nut on board end of turnbuckle assembly using a ½” wrench (FIGURE 2). Threads are right-hand threads. -
Page 19: Troubleshooting
tROUbLESHOOtiNg In the event the Power Foundation fails to operate, investigate the symptoms and possible solutions provided in the chart below: SOLUtiON SyMPtOM • Verify power cord is plugged into a working, grounded Hand control illuminates and appears to be electrical outlet. - Page 20 [ power foundations ] MAdE iN tHE USA NAtiONWidE cUStOMER SERvicE toll free: (800) 888-3078 PowerFoundations.com © 2011 Leggett & Platt Consumer Products Group, a division of Leggett & Platt, Incorporated...
This manual is also suitable for:
S-cape platformSilhouettePro-motionBronze
